Main Categories
    Filters
    Preferences
    Search

    Tools & Supplies

    Tools & Supplies

    View as Grid List
    Sort by
    Display per page

    myParts Kit from Texas Instruments: Companion Parts Kit for NI myDAQ

    #6002-240-001
    $128.25
    ( 14 In stock)

    The kit comes with a collection of parts that are the building blocks of all electronics, including op-amps, an instrumentation amplifier, a comparator, voltage regulators, switching regulators, digital logic gates, timers, temperature sensors, data converters, transistors, resistors, capacitors, LEDs, switches, a wiring kit and more.

    myProto Protoboard

    #6002-410-007
    $49.99
    ( 2 In stock)

    The Digilent myProto accessory board for the NI my-DAQ and NI my-RIO brings all your my-DAQ/my-RIO's signals to breadboard connections where they can be easily accessed using simple jumper wires, and even adds several useful I/O devices.

      mySTEM Project Board for NI myDAQ

      #13-07-69007
      $129.00
      (In stock)

      The  mySTEM™ Control & Project Board for NI myDAQ is an essential tool for the introduction of control systems. It is ideal for teaching and learning science, technology, engineering and mathematics. The mySTEM™ Project Board comes with learning resources that may be used by any beginner in the STEM field to gather data, make decisions and control output devices. It allows students to control the state and direction of four output channels that support a wide range of field devices.

       

      Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. We recommend the Spare Parts Store to create your own project.

       

      Includes:

      • S-Motor
      • Mini Switch
      • resisters
      • wires
      • flat plugs

      Note:  mySTEM Project Board comes with US Plug. You can easily use into different plug with common US->EU or other adapters. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. 

      myVTOL for NI myDAQ (for Classrooms)

      #myVTOL-GP
      Request Quote
      myVTOL mini system will help teach basic flight dynamics, motion control, and PID control. This vertical takeoff and landing system uses a variable PC fan to create lift for one degree of freedom plant and can hover, take off, and land vertically much like a helicopter or harrier jet.


      Note: Can run on 9 volt battery (included) or external 9 volt power pack.

      NI myDAQ - for K12 Classrooms

      #NI-MYDAQ-CLASS-GP
      Request Quote

      National Instrument's NI myDAQ is designed to give students the ability to work on engineering course work and experiment with projects hands-on anywhere, anytime. The NI myDAQ is a high-quality instrumentation device gives student's the power to prototype systems and test circuits outside of the classroom while improving comprehension with continuous reinforcement.

       

      For all Classroom options and Quotations, please contact an Account representative for more information, and to discuss your specific needs.

       

       

      Powerpole 45 Extension Cable, 14AWG, 50cm

      #70021
      $12.95
      (In stock)

      The Powerpole Extension Cable is 50cm long and 14AWG wire gauge to handle heavier loads.

      PWM cable Set - TJC8 3 pin, 22AWG, F-F - 12 pcs

      #71011
      $15.99
      (In stock)

      This set of 12 pieces includes,

      • 2 x 20cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
      • 2 x 40cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
      • 2 x 60cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
      • 6 x 3pin Dupont male to male connectors

      Seeed Studio Grove - Universal 4 Pin 20cm Unbuckled Cable - Pack of 5

      #ACC11317O
      $1.99 $2.95
      ( 1 In stock)
      Compared with the Electronic Brick system, the Grove System uses only 1 type of cable, (the Electronic Brick system uses 4). These cables are compatible with all modules included in the Grove system.

      Seeed Studio Grove - Universal 4 Pin Buckled 5cm Cable - Pack of 5

      #ACC83054O
      $1.49 $2.95
      ( 12 In stock)
      The Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Twigs to the Stem - Basic Shield or to other Twig compatible boards for quick prototyping. As a lot of users ask for different length of cables, so we made the 5cm,20cm,30cm,40cm,and 50cm cables for different applications.

      Seeed Studio Grove Conversion Cable - Pack of 5 (4 pin Female Jumper to Grove 4 pin)

      #ACC17112O
      $2.99 $4.95
      ( 9 In stock)

      With this wire, you can easily connect all of Seeed Grove modules to any 2.54mm pitch connectors. 5 PCs is included in one pack.Length of each wire is 20cm. Note: Grove side uses buckled connector.

      Snap Circuits - Bric Structures

      #SCBRIC1
      $19.99 $34.95
      ( 1 In stock)

      Kids can use their imagination to combine SNAP CIRCUITS® with ordinary building bricks and make endless combinations of construction and circuitry. 

      Snap Circuits - Student Guide for SC-100R

      #753294
      $3.99 $9.95
      ( 5 In stock)

      Snap Circuits® Student Guide for SC-100/SC-100R. Student Guide has 48 color pages. For an enhanced learning experience because it teaches electronics. Includes quizzes to verify learning.

      USB cable type A/B

      #A000045
      $1.79
      ( 94 In stock)

      Standard USB 2.0 cable. Use it to connect Arduino Uno, Arduino Mega 2560, or any board with the USB female A port of your computer. Cable length is approximately 178cm.

      USB Cable, Type A to Type C, Blue, 1M

      #70186
      $5.99
      (In stock)

      USB Cable, Type A to Type C, Blue, 1 Meter, male to male

      Vernier myDAQ Adapter

      #BT-MDAQ
      $69.00
      ( 16 In stock)

      The adapter includes two connectors for Vernier analog sensors and one connector for Vernier digital sensors. A screw terminal and header pins provide access to myDAQ lines not used by the connectors. This includes the two analog output lines, three digital lines (including the digital lines with the frequency and pulse width modulation outputs), and a +5 volt power terminal.

      VMX Battery Adapter Cable

      #70167
      $2.99
      ( 17 In stock)

      The VMX Battery Adapter cable connects a VMX-pi power connector to an external battery supply.