This Chemistry Lab Kit includes 8 safe to use chemicals, 80 safety tested experiments. Comes with complete instruction manual

The NI myDAQ student data acquisition device is designed to give students the ability to work on engineering course work and experiment with projects hands-on anywhere, anytime. The myDAQ is a high-quality instrumentation device that gives students the power to prototype systems and test circuits outside of the classroom and improve comprehension with continuous reinforcement. (This version of the myDAQ is only for sale to students in the USA).

Special Offer: Optional accessory -  myGRID for NI myDAQ - an AC power grid that helps to investigate the components of a power grid - is available as a bundled purchase - click the checkbox below - while supplies last.

Special Offer: Optional accessory -  myGRID for NI myDAQ - an AC power grid that helps to investigate the components of a power grid - is available as a bundled purchase - click the checkbox below - while supplies last.

The myDevBoard is an accessory board designed to connect directly to the NI myDAQ hardware. The Protoboard consists of a prototyping space as well as each I/O line from NI myDAQ broken out through quad contact blocks to make wiring easier. 

Includes,

• NI myDAQ terminal block and female headers
• 9 V battery holder to add supplemental voltage and current
• Includes switch to select between battery or external power using AC Adapter or bench top power supply. (Battery, AC adapter and bench top power supply not included)
• 3 AMP Auto reset fuse
• Segmented power rails on main bread board
• Large ground plane underneath main bread board 

The kit comes with a collection of parts that are the building blocks of all electronics, including op-amps, an instrumentation amplifier, a comparator, voltage regulators, switching regulators, digital logic gates, timers, temperature sensors, data converters, transistors, resistors, capacitors, LEDs, switches, a wiring kit and more.

The Digilent myProto accessory board for the NI my-DAQ and NI my-RIO brings all your my-DAQ/my-RIO's signals to breadboard connections where they can be easily accessed using simple jumper wires, and even adds several useful I/O devices.

The  mySTEM™ Control & Project Board for NI myDAQ is an essential tool for the introduction of control systems. It is ideal for teaching and learning science, technology, engineering and mathematics. The mySTEM™ Project Board comes with learning resources that may be used by any beginner in the STEM field to gather data, make decisions and control output devices. It allows students to control the state and direction of four output channels that support a wide range of field devices.

Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. We recommend the Spare Parts Store to create your own project.

Includes:

• S-Motor
• Mini Switch
• resisters
• wires
• flat plugs

Note:  mySTEM Project Board comes with US Plug. You can easily use into different plug with common US->EU or other adapters. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. 

Programmable Xilinx 7020 FPGA NI ELVIS—The NI Engineering Laboratory Virtual Instrumentation Suite (NI ELVIS) III is an engineering laboratory device developed for project-based learning.

The National Instruments myRIO-1900 is a portable reconfigurable I/O (RIO) device that students can use to design control, robotics, and mechatronics systems.
 

For motor control, use the MD2 Motor Driver

• 1- 140 piece Jump Wire Kit
• 1- 370 piece 1/4W Resistor Kit
• 1- 100 piece Capacitor Component Kit
• 1 - Choke, Axial, Conformal, 1000 uH 5% Inductor
• 2 - 1000 pF 100 Volt Silver Mica Capacitor BC# 8860720
• 3 - Inductor, Toroid, Vertical, 1000.0 uH, 1.3 IDC, 0.4 OHM
• 3 - IC OP amp GP 1MHZ 8DIP
• 1 - 9V battery
• 1 - Alligator Clips

This student bundle for University of North Dakota - EE313L, includes:

• 1 - 10K OHM 5% 1/4W AXIAL Resistor
• 1 - 1K OHM 5% 1/6W AXIAL Resistor
• 1 - 100 OHM 5% 1/4W AXIAL Resistor
• 1 - 120 OHM 5% 1/4W AXIAL Resistor
• 1 - 200 OHM 5% 1/6W AXIAL Resistor
• 1 - 5 OHM 5% 5W AXIAL Resistor
• 1 - 16K OHM 5% 1/4W AXIAL Resistor
• 1 - CER 1UF 25V X7R RADIAL Capacitor
• 1 - FIXED IND 10MH 170MA 10.86OHM TH
• 1 - FIXED IND 1MH 100MA 20 OHM TH
• 1 - SWITCH SLIDE SPDT 0.4VA 28V
• 1 - CER 10UF 50V X7S RADIAL Capacitor
• 1 - CER 10000PF 400VAC Y5V RAD Capacitor
• 1 - 16 OHM 5% 1/4W AXIAL Resistor
• 1 - Carbon Film 20 Ohm 1/4 Watt 5% Resistor
• 1 - Carbon Film 8.2k Ohm 1/4 Watt 5% Resistor

• 1 - 9V battery
• 1 - Thermistor 10k
• 5 - LED indicators - Red
• 2 - 1.5MHZ 8DIP Op-Amps
• 2 - 1kΩ Resistors
• 2 - 4.7kΩ Resistors
• 2 - 3.3kΩ Resistors
• 2 - 2.2kΩ Resistors
• 2 - 15kΩ Resistors
• 3 - 7.5kΩ Resistors
• 1 - Thermistor PTC 100 Ohm 2 Pin
• 1 - Thermistor NTC K +/-10% 100k Ohm
• 1 - 1/2" Circular Force Sensing Resistor
• 1 - 1.5 To 24 Volt Motor Grab Bag