The Studica Linear Servo RC Actuator 140-200 is a new Servo motor which has a stroke of 140mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.

The Studica Linear Servo RC Actuator 140-50 is a new Servo motor which has a stroke of 140mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.

The Studica Linear Servo RC Actuator 50-200 is a new Servo motor which has a stroke of 50mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.

The Studica Linear Servo RC Actuator 50-50 is a new Servo motor which has a stroke of 50mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.

The Maverick 12V DC Gear Motor 61:1 w/Encoder was designed for strength to endure competitions, providing a stall torque of 65 min. kgf-cm.

Includes,

• 4 - Maverick 12V DC Gear Motor w/Encoder  75001
• 4 - Motor Mount Plate  76140
• 4 - Motor Mount Clamp Kit  76141
• 1 - M3 x 10mm Button Head Cap Screw (pack of 50)  76203-50

The Studica Multi-Mode Smart Servo features all-steel gears and large amounts of torque. This angular programmable Servo can fill a variety of roles on your robot or project. In standard mode, it operates on a +/- 150-degree range. Using the Studica Smart Robot Servo Programmer (sold separately) the Multi-mode Smart Servo can be configured to run in continuous, standard, and custom angular mode. In continuous rotation mode, the servo will have proportional speed control based on the PWM signal that you send with your servo controller.  

Servocity - Operating Specifications:

• Operating Voltage Range: 6~12VDC
• Rated Voltage: 12VDC
• Rated Load: 4.5 kgf-cm (62.5 oz-in)
• Operating Temperature: -10 ~ +60°C
• Max No-Load Current: 0.52A
• No-Load Speed: 313 RPM
• Min. Stall Torque: 30 kgf-cm (416.6 oz-in)
• Max. Stall Current: 20A @ 12VDC
• Dielectric Strength: 250 VAC
• Motor Brush Type: Graphite
• Output Power at Max. Efficieny: 13W
• Gear Type: Planetary
• Gear Ratio: 27:1
• Bearing Type: Dual Ball Bearing
• Shaft size: 6mm (0.236”)
• Net Weight: 330g (11.64oz)

• Operating Range: 3-12VDC
• Torque @ Max Efficiency: 205 oz-in. (12V)
• Torque @ Stall: 992 oz-in.@12VDC
• Stall Current: 0.5A @ 12VDC
• Gear train damage can occur if stalled (locked)
• .240” (6mm) Diameter Shaft
• No load current: 45mA
• No load current @ Max Efficiency: 160mA
• No load speed: 4 RPM
• No load speed @ Max Efficiency: 2.8 RPM
• Gear ratio: 900:1
• Motor size: 1.30"Dia. x 1.015"L
• Gear size: 1.45"Dia. x 1.15"L
• Shaft size: 6mm (0.236”) Dia. x 0.715"L
• Weight: 0.2938 lbs. (4.7 oz.)
• DC reversible motors
• Solder type terminal
• High torque construction
• Oil bearing design for long service life
• Insulation resistance: 10 MOhm
• Dielectric Strength: 300VDC

Operating Specifications:

• Operating Voltage Range: 6~12VDC
• Rated Voltage: 12VDC
• Rated Load: 2.3 kgf-cm (31.9 oz-in)
• Operating Temperature: -10 ~ +60°C
• Max No-Load Current: 0.52A
• No-Load Speed: 612 RPM
• Min. Stall Torque: 16 kgf-cm (222.2 oz-in)
• Max. Stall Current: 20A @ 12VDC
• Dielectric Strength: 250 VAC
• Motor Brush Type: Graphite
• Output Power at Max. Efficieny: 13W
• Gear Type: Planetary
• Gear Ratio: 14:1
• Bearing Type: Dual Ball Bearing
• Shaft size: 6mm (0.236”)
• Net Weight: 330g (11.64oz)

Makeblock 820 Coreless Motor has both the  positive pitch and the negative pitch, it is usually used in the four-axis aircraft.

Makeblock air pump motor - DC 12V/370-02PM is widely used for aquarium tank oxygen circulate, a DIY project to fit your needs.

Makeblock air pump motor - DC 12V/3202PM is widely used for aquarium tank oxygen circulate, it can also be used for a DIY project that you dream up.

DC motors are the most commonly used motors in Makeblock Platform. With Makeblock DC Motor-25 Brackets, they may be easy to connet to Makeblock structural components.

Makeblock DC Motor-37 Bracket is an easy to use fastener for a DC Motor. These specially designed brackets help attach the motor to your maker project. They are compatible with a 37mm DC motor and most Makeblock components.

MEDS15 Servo Motor Bracket is specifically designed to attach the MEDS15 Servo to your maker project. Made with durability and versatility in mind, this bracket is made from 6061 aluminum that is 2mm thick.

Makeblock mini metal gear motor has a mini body, delicate gears and easy connector, and is widely used many DIY projects.

Makeblock has three different revolving speed for your choice.

Specification:

• Rated Voltage: DC 12V
• Revolving Speed: 100RPM/210RPM/390RPM (Depends on your needs)
• Total Size : 46 x 12mm
• Operating Temperature Range: -20?~+60?

Makeblock mini metal gear motor has a mini body, delicate gears and easy connector, and is widely used many DIY projects.

Makeblock has three different revolving speed for your choice.

Makeblock mini metal gear motor has a mini body, delicate gears and easy connector, and is widely used many DIY projects.

Makeblock has three different revolving speed for your choice.

Makeblock Worm Geared Motor Bracket A (PMMA) is a bracket specially designed for 370 Worm Geared Motor. This bracket enables you fix the 370 Worm Geared Motor on other Makeblock components to create more interesting projects.

his module is the updated version of the previous Me 130 motor. It has the same dimension as before but now is added a RJ25 port and motor drive chip. The module does not require motor driver port as it can rotate with dual-digital port. It supports Arduino but not the mBlock of mBot.

This module is designed to drive stepper motors. It uses DRV8825 chip and has a maximum driving current of 2.5A. The DRV8825 is a complete micro-stepping motor driver with built-in translator for easy operation. It is designed to operate bipolar stepper motors in full, 1/2, 1/4, 1/8/ 1/16, or 1/32 step modes. We add an on-board potentiometer, so you can change the current of motor easily.

Use the Motor Mount Clamp kit when fastening motors on body and attaching kit to channel and other structure.

• Step File Top
• Step File Bottom

The Motor Mount Plate is used with the Maverick 12V DC Gear Motor  (Part# 75001) to attach it inside the anyone of the U Channels 76010 to 76018. This is an example of a chassis with 4 motors mounted inside the U-Channel using a Motor Mounting Plate.

• Step File

The motor mount plate leaf is ideal for use with robotics design.

• Step File

Learn How to Control Motors, Sensors & Actuators with LabVIEW & NI myRIO.

The Robotics Sensor & Motor Training Kit from Studica is an affordable and turnkey solution that allows you to teach your students how to control sensors and motors using LabVIEW and NI myRIO. It includes two project boards, one with different motors and the other board with most of the standard robotics sensors.

(NI myRIO, LabView and computer are not included).